[Message Prev][Message
Next][Thread Prev][Thread Next][Message
Index][Thread Index]
Re: Re: [OT] Asterisk at home help + XAP integration
Hi Chris
Might be an idea to have a look at CQC software....Some nice
Graphics ...They have a CBUS Plugin and there was talk of having a xAP
plugin....
http://www.charmedquark.com/
Go into the Forum section and theres a CBUS thread with some nice
touchscreen pics ...
HTH
Frank
----- Original Message -----
From: "Chris Purves" <CHRIS_PURVES@xxxxxxx>
To: <ukha_d@xxxxxxx>
Sent: Wednesday, October 19, 2005 8:37 PM
Subject: [ukha_d] Re: [OT] Asterisk at home help + XAP integration
Paul - any chance of a copy of your config files ? I have not even
gone near that aspect yet but have printed a ton of stuff from the net
that might help me. You're not using sipgate by any chance are you ?
I always struggle to understand the difference between xap and xpl. I
have only used xap so far (with CBUS via the CBUS/XAP gateway).
I have 3 touchpanels around the house so I am keen to get integrating
when support arrives.
Ta
Chris
--- In ukha_d@xxxxxxx, "Paul Gale" <groups@s...> wrote:
>
> xAP support for Asterisk is still being worked on but I've not heard
anything for a couple of weeks. Should be good though - I've asked for
message waiting support which would allow good integration into my HA
network.
>
> I have the same config as you - Dell server, *@H, SPA3000 - works
really well.
>
> Paul.
>
> > -----Original Message-----
> > From: ukha_d@xxxxxxx [mailto:ukha_d@xxxxxxx] On
Behalf Of
> > Ian Lowe
> > Sent: 19 October 2005 11:01
> > To: ukha_d@xxxxxxx
> > Subject: RE: [ukha_d] [OT] Asterisk at home help + XAP
integration
> >
> > Asterisk at Home has xPL built in, not xAP.
> >
> > If you have xAP bits and bobs already, I think there's a xAP
module for
> > Asterisk (not quite sure about the mechanics of AAH vs Asterisk
raw there)
> > -
> > I'm sure Patrick or Kevin mentioned that previously?
> >
> > If you don't have an existing set of tools, have a look at xPL.
(there's a
> > yahoo group over here: ukha_xpl@xxxxxxx )
> >
> > Ian.
> >
> > -----Original Message-----
> > From: ukha_d@xxxxxxx [mailto:ukha_d@xxxxxxx] On
Behalf Of
> > christopher purves
> > Sent: 19 October 2005 10:43
> > To: ukha_d@xxxxxxx
> > Subject: [ukha_d] [OT] Asterisk at home help + XAP integration
> >
> > Hi All,
> >
> > Well I have finally installed *@home and as I know quite a few of
you use
> > it
> > I wanted comments on my master plan before I set out to check I'm
not
> > being
> > an idiot.
> >
> > I have installed *@Home on a Dell £99 server (TM) and that all
seems fine
> > -
> > painless install.
> >
> > I propose the following - use Linksys PAB2 adapters on all fixed
analogue
> > phones in the house. Buy a sipura 3000 to connect in the POTS
land
line
> > and
> > to plug an 'emergency' phone into - on a power fail a relay in
the
sipura
> > bridges the FXO and FXS ports so I can still use the emergency
phone no
> > matter what.
> >
> > I have a couple of sipgate numbers now - I was gonna use one for
voice and
> > one for fax and route appropriately.
> >
> > I think I simply need to enable XAP in the * config to get XAP
messages ?
> >
> > Does that make some kinda sense?
> >
> > Ta
> > Chris
> >
> >
> >
> >
> >
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
> >
> >
> >
>
UKHA_D Main Index |
UKHA_D Thread Index |
UKHA_D Home |
Archives Home
|