The UK Home Automation Archive

Archive Home
Group Home
Search Archive


Advanced Search

The UKHA-ARCHIVE IS CEASING OPERATIONS 31 DEC 2024


[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: Electronics Question


  • To: <ukha_d@xxxxxxx>
  • Subject: RE: Electronics Question
  • From: "Dr John Tankard" <john@xxxxxxx>
  • Date: Sun, 24 Feb 2002 11:19:23 -0000
  • Delivered-to: mailing list ukha_d@xxxxxxx
  • Mailing-list: list ukha_d@xxxxxxx; contact ukha_d-owner@xxxxxxx
  • Reply-to: ukha_d@xxxxxxx

Title: Message
Sorry Keith, I did not get your reply, I have only just spotted it on the web, looks like Yahoo is playing up
 
John
-----Original Message-----
From: Keith Doxey [mailto:lists.diyha@xxxxxxx]
Sent: 24 February 2002 09:23
To: ukha_d@xxxxxxxSubject: RE: [ukha_d] Electronics Question

The MAX232 I posted to the list yesterday includes voltage doublers and converters all in a single 16pin DIP.
 
In fact I was building a test board last night with a MAX232 and PIC 16F628.
 
Keith
-----Original Message-----
From: Dr John Tankard [mailto:john@xxxxxxx]
Sent: 24 February 2002 06:50
To: ukha_d@xxxxxxxSubject: RE: [ukha_d] Electronics Question

> Hi,
>
> I'd like to take a data signal clocked at 1200 Baud, from a battery
> powered deivce (power is 3x1.5V AAA) for connection to a
> serial input at
> either 5V or RS232 levels, any suggestions on the best way to do this.
>
> Note I only need to read the data.

I assume the question you are asking is how do I get the required
voltage to run rs232 ? If that is what you want then you could look at a
DC-DC converter, mamim do them from memory
http://dbserv.maxim-ic.com/PowerSupplies.cfm

Or if you don't heed a higher voltage for any other parts of you design
you could look at a rs232 driver with voltage conversion built in. Again
Maxim do loads of theses but I can't remember the part numbers, take a
look on the same site under interface.

John





For more information: http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.


For more information: http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

Yahoo! Groups Sponsor
ADVERTISEMENT

For more information: http://www.automatedhome.co.uk
Post message: ukha_d@xxxxxxx
Subscribe:  ukha_d-subscribe@xxxxxxx
Unsubscribe:  ukha_d-unsubscribe@xxxxxxx
List owner:  ukha_d-owner@xxxxxxx

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

Home | Main Index | Thread Index

Comments to the Webmaster are always welcomed, please use this contact form . Note that as this site is a mailing list archive, the Webmaster has no control over the contents of the messages. Comments about message content should be directed to the relevant mailing list.